LUXIAOJUN 20KG Mastery Stainless Steel Power Bar
The LUXIAOJUN 20KG Mastery Stainless Steel Power Bar is built for powerlifting training, combining an aggressive grip with construction that holds up over the long haul. Both the shaft and sleeves are made entirely from stainless steel, so there's no coating to wear down or flake off over time. That means low maintenance and strong corrosion resistance, even in humid gyms or garage setups.
This bar features a 29mm shaft, thicker than a standard Olympic bar, which keeps flex to a minimum and gives you a stable, locked-in feel under heavy loads on squats, bench, and deadlifts. Overall length is 2200mm (86.6") with a 1310mm (51.57") shaft length and a 433mm (17") loadable sleeve length, weighing a true 20kg (44.1 lbs) within a tight tolerance for consistent training.
The knurling is aggressive, with 1.5mm width and 0.5mm depth across a 5-section pattern, the most aggressive grip in the LUXIAOJUN power bar lineup. A center knurl keeps the bar secure on your back during heavy squats, and smooth 50mm sleeves are fully compatible with standard 2" Olympic plates.
Rated to 200 KPSI with a 680kg (1,500 lb) weight capacity, this bar is built to take on the heaviest training sessions. The low whip design helps you maintain form and stability when the bar is loaded heavy. Backed by a lifetime warranty against manufacturing defects, the LUXIAOJUN Mastery Power Bar is a dependable choice for serious lifters who want a bar that lasts.
Grip, shaft and finish.
It runs in a 5-section pattern and it is the most aggressive grip in the LUXIAOJUN power bar lineup. A center knurl keeps the bar where you put it on your back under a heavy squat.
The extra diameter keeps flex to a minimum. Loaded heavy for squats, bench and deadlifts, it feels stable and locked in.
Both are made entirely from stainless steel, so there is no coating to wear down or flake off over time. Upkeep stays low and corrosion resistance stays strong, even in a humid gym or a garage setup.
| Bar weight | 20 kg (44.1 lb) |
|---|---|
| Weight tolerance | +/- 1% |
| Shaft diameter | 29 mm |
| Overall length | 2200 mm (86.6 in) |
| Shaft length | 1310 mm (51.57 in) |
| Loadable sleeve length | 433 mm (17 in) |
| Sleeve diameter | 50 mm |
| Sleeve surface | Smooth |
| Rating | 200 KPSI |
| Weight capacity | 680 kg (1,500 lb) |
| Whip | Low |
| Knurl | Aggressive, 1.5 mm wide, 0.5 mm deep |
| Knurl pattern | 5-section |
| Center knurl | Yes |
| Finish | Stainless steel, shaft and sleeves |
| Plate fit | Standard 2 in Olympic |
| Built for | Powerlifting training |
Lifetime warranty against manufacturing defects.
Every LUXIAOJUN product carries a lifetime warranty against manufacturing defects. If a fault in materials or workmanship appears, we put it right for as long as you own the product.
The warranty covers how the product was made, not how it was used. Normal wear from training, cosmetic marks, and damage caused by misuse, modification, improper assembly or improper storage fall outside it.
To start a claim, contact us with your order number and photographs of the issue.
It is the most aggressive grip in the LUXIAOJUN power bar lineup, 1.5 mm wide and 0.5 mm deep in a 5-section pattern. There is a center knurl, which is what holds the bar on your back through a heavy squat.
The sleeves are 50 mm and smooth, and they are compatible with standard 2 in Olympic plates. You get 433 mm (17 in) of loadable sleeve on each side.
A true 20 kg (44.1 lb), held to plus or minus 1 percent, so the load on the bar reads the same session after session.
It is built for powerlifting training. The 29 mm shaft is thicker than a standard Olympic bar and the whip is low, which keeps the bar stable under heavy squats, bench and deadlifts.
There is no coating on it to wear down or flake off, which is what keeps maintenance low and corrosion resistance strong. It holds up in humid gyms and garage setups.
